Also move RangeSet into a header file to make it testable, and add unit
tests.
In RangeSet::Parse() (the former parse_range()), use libbase logging to
do assertions. This has the same effect as the previous
exit(EXIT_FAILURE) to terminate the updater process and abort an update.
The difference lies in the exit status code (i.e. WEXITSTATUS(status) in
install.cpp), which changes from 1 (i.e. EXIT_FAILURE) to 0.
Test: recovery_unit_test
Test: Apply an incremental update with the new updater.
Change-Id: Ie8393c78b0d8ae0fd5f0ca0646d871308d71fff0
Update_verifier will reboot the device if it fails to read some blocks
on the care_map when veritymode=eio. Also make some partition name
changes to match the care_map.txt.
Test: Update_verifier reboots the device after read failures in eio mode.
Change-Id: Icf68e6151dee72f626a9ab72946100cf482a4e6c
LOG(INFO) already appends a newline. Don't print redundant newline.
Test: No extra blank lines when calling ui_print(). And on-screen UI
shows the same.
Change-Id: I74e9a8504a7146a6cb3dae02fe2406d0dd54069b
Per the comment in build/make/core/base_rules.mk:
Ninja has an implicit dependency on the command being run, and kati will
regenerate the ninja manifest if any read makefile changes, so there is no
need to have dependencies on makefiles.
Test: mmma bootable/recovery
Change-Id: I27b97df10d40f39ad966be70b33811175a665439
Then rename RangeSinkState to RangeSinkWriter. RangeSinkWriter reads
data from the given FD, and writes them to the desination RangeSet.
Test: Apply an incremental with the new updater.
Change-Id: I5e3ab6fc082efa1726562c55b56e2d418fe4acaf
fs_mgr_read_fstab_default() is now aware of recovery mode so it's ok to
switch to this new API.
Bug: 35811655
Test: recovery boot sailfish
Change-Id: I1025b606fd96e74a893ae99cefc1da01e4b27a23
Raise the priority and ioprio of update_verifier and launch with
exec_start. This saves ~100ms of time before `class_start main` is executed.
Bug: 36511808
Bug: 36102163
Test: Boot bullhead
Test: Verify boottime decrease on sailfish
Change-Id: I944a6c0d4368ead5b99171f49142da2523ed1bdd
Log the maximum temperature as well as the start/end temperature of an
update to last_install. Check the temperature at the end of each
block_image_update(verify). To get the maximum temp, we iterate through
/sys/class/thermal/thermal_zone*/temp and find the maximum value
present.
Bug: 32518487
Test: temperature logs in last_install
Change-Id: Iaf22a9fbc5b18611bbc5320ffea995417872e514
Also factor out the common parts in {setup,clear}_bcb into a separate
function.
Test: recovery_component_test
Change-Id: I7b95cced925c8135e020dcb791ca2425d4f28449
Mostly for applypatch family APIs like ApplyBSDiffPatch() and
ApplyImagePatch(). Changing to size_t doesn't indicate they would
necessarily work with very large size_t (e.g. > ssize_t), just
similar to write(2). But otherwise accepting negative length doesn't
make much sense.
Also change the return type of SinkFn from ssize_t to size_t. Callers
tell a successful sink by comparing the number of written bytes against
the desired value. Negative return values like -1 are not needed. This
also makes it consistent with bsdiff::bspatch interface.
Test: recovery_component_test
Test: Apply an incremental with the new updater.
Change-Id: I7ff1615203a5c9854134f75d019e266f4ea6e714
Tianjie Xu
Tao Bao
Bowgo Tsai
Treehugger Robot
Dan Shi
Tom Cherry