This will be used for testing purpose only, replacing the previously
used "fail", to intentionally abort an update.
As we're separating the logic between commands parsing and execution,
"abort" needs to be considered as a valid command during the parsing.
Test: recovery_unit_test and recovery_component_test on marlin.
Change-Id: I47c41c423e62c41cc8515fd92f3c5959be08da02
This is a stress test that instantiates multiple testcases that
interrupt a BBOTA update at every transfer command. Each testcase
asserts the last_command_file after the interruption, verifies the
update resumability, then resumes the update and asserts the updated
image.
The transfer list in the testcase covers most of the transfer commands
(stash/free/move/bsdiff/zero/new), as well as some special pattern like
having duplicate stash ids.
This CL also addresses one issue in the updater code, by resetting the
stash_map before each run. The stash map should be valid only per
block_image_verify/block_image_update run. Having leftover may cause
issue in subsequent runs, in particular when calling block_image_verify
after a previous run of block_image_{update,verify}.
Test: Run recovery_component_test on marlin.
Change-Id: I6f9a0368d194a754ce41a9c9819c6d5be2657248
Otherwise tests may interfere with each other by using the same / default
location.
Test: Run recovery_component_test on marlin.
Change-Id: I6b0455489f2fdce819009964dd92bfd9bfeb06ef
Move the common codes into RunBlockImageUpdate(). Also clean up the
partition updated marker after running each test.
Test: Run recovery_component_test on marlin.
Change-Id: Id4302e4da4c664231b737a1e83d2e164ef58ed97
We have a general need for overriding more paths (e.g. "/tmp"), mostly
for testing purpose. Rename CacheLocation to Paths, and use that to
manage TEMPORARY_{INSTALL,LOG}_FILE.
Test: mmma -j bootable/recovery
Test: recovery_component_test
Change-Id: Ia8ce8e5695df37ca434f13ac4d3206de1e8e9396
This class allows us to set the following locations dynamically:
cache_temp_source, last_command_file, stash_directory_base.
In the updater's main function, we reset the values of these variables
to their default locations in /cache; while we can set them to temp
files in unit tests or host simulation.
Test: unit tests pass
Change-Id: I528652650caa41373617ab055d41b1f1a4ec0f87
When performing an update, save the index and cmdline of the current
command into the last command file if this command writes to the stash
either explicitly of implicitly. This mitigates the overhead to update
the last command file for every command. I ran a simple test on angler
and the time to update 1000 times is ~2.3 seconds.
Upon resuming an update, read the saved index first; then
1. In verification mode, check if all commands before the saved index
have already produced the expected target blocks. If not, delete the
last command file so that we will later resume the update from the
start of the transfer list.
2. In update mode, skip all commands before the saved index. Therefore,
we can avoid deleting stashes with duplicate id unintentionally;
and also speed up the update.
If an update succeeds or is unresumable, delete the last command file.
Bug: 69858743
Test: Unittest passed, apply a failed update with invalid cmd on angler
and check the last_command content, apply a failed update with invalid
source hash and last_command is deleted.
Change-Id: Ib60ba1e3c6d111d9f33097759b17dbcef97a37bf
bsdiff interface is changing such that it hides the suffix array
pointer from the public interface. This allows to use a different
suffix array data size depending on the input size, running much faster
in the normal case.
Bug: 34220646
Test: `make checkbuild`; Ran an incremental update generation on a non-A/B device.
Change-Id: I78e766da56cf28bc7774b8c8e58527bc11d919fb
The thread to receive new data may still be alive after we exit
PerformBlockImageUpdate() upon failures. This caused memory corruption
when we run the unittest repeatedly. Set the receiver_available flag
to false and make sure the receiver exits when the update fails.
Bug: 65430057
Test: unittests passed with tsan
Change-Id: Icb232d13fb96c78262249ffbd29cdbe5b77f1fce
Also drop the "bootable/recovery" path in LOCAL_C_INCLUDES from
applypatch modules.
Test: lunch aosp_{angler,bullhead,fugu,dragon,sailfish}-userdebug;
mmma bootable/recovery
Change-Id: Idd602a796894f971ee4f8fa3eafe36c42d9de986
This reverts commit 26436d6d60 to re-land
"Move error_code.h into otautil.".
This way it stops requiring relative path ".." in LOCAL_C_INCLUDES
(uncrypt and edify). Soong doesn't accept non-local ".." in
"local_include_dirs".
This CL needs to land with device-specific module changes (e.g. adding
the dependency on libotautil).
Test: lunch aosp_{angler,bullhead,dragon,fugu,sailfish}-userdebug;
mmma bootable/recovery
Change-Id: If193241801af2dae73eccd31ce57cd2b81c9fd96
This way it stops requiring relative path ".." in LOCAL_C_INCLUDES
(uncrypt and edify). Soong doesn't accept non-local ".." in
"local_include_dirs".
Test: mmma bootable/recovery
Change-Id: Ia4649789cef2aaeb2785483660e9ea5a8b389c62
Otherwise the test may fail after a large number of iterations due to
file open failure.
Bug: 65430057
Test: run recovery_component_test on sailfish for 2000 iterations.
Change-Id: I0d456284d6064467038911d63eade95740cbec2c
receive_new_data may exit too early if the zip processor has sent all
the raw data. As a result, the last few 'new' commands will fail even
though the brotli decoder has more output in its buffer.
Restruct the code so that 'NewThreadInfo' owns the decoder state solely;
and receive_brotli_new_data is responsible for the decompression.
Also reduce the test data size to 100 blocks to avoid the test timeout.
Bug: 63802629
Test: recovery_component_test. on bullhead, apply full updates with and
w/o brotli compressed entries, apply an incremental update.
Change-Id: I9442f2536b74e48dbf7eeb062a8539c82c6dab47
Add a new writer that can decode the brotli-compressed system/vendor
new data stored in the OTA zip.
Brotli generally gives better compression rate at the cost of slightly
increased time consumption. The patch.dat is already compressed
by BZ; so there's no point to further compress it.
For the given 1.9G bullhead system image:
Size: 875M -> 787M; ~10% reduction of package size.
Time: 147s -> 153s; ~4% increase of the block_image_update execution time.
(I guess I/O takes much longer time than decompression.)
Also it takes 4 minutes to compress the system image on my local
machine, 3 more minutes than zip.
Test: recovery tests pass && apply a full OTA with brotli compressed
system/vendor.new.dat on bullhead
Change-Id: I232335ebf662a9c55579ca073ad45265700a621e
package_extract_dir() was removed in go/aog/402383, and the
corresponding UpdaterTest should be removed as well.
Bug: 62918308
Test: mma && code search
Change-Id: Ibe9c473a5d41d2fa4d26abca5684e71b104891b0
Right now the update stuck in a deadlock if there's less new data than
expection. Add some checkers and abort the update if such case happens.
Also add a corresponding test.
Bug: 36787146
Test: update aborts correctly on bullhead && recovery_component_test passes
Change-Id: I914e4a2a4cf157b99ef2fc65bd21c6981e38ca47
It's valid to provide only 1 argument to apply_patch_check(). We
shouldn't fail the argument parsing.
Bug: 36541737
Test: recovery_component_test passes.
Test: recovery_component_test captures the failure without the fix.
Test: The previously failed update applies successfully.
Change-Id: Iee4c54ed33b877fc4885945b085341ec5c64f663
And switch them to std::vector & std::unique_ptr
Bug: 32117870
Test: recovery tests passed on sailfish
Change-Id: I5a45951c4bdf895be311d6d760e52e7a1b0798c3
This CL removes the updater support for delete(), symlink(), rename(),
set_metadata() and set_metadata_recursive(). Such functions have been
removed from the generation script in commit
f388104eaacd05cfa075d6478369e1d0df5ddbf3 (platform/build).
Note: This CL also removes delete_recursive() which seems to have never
been supported in generation script.
Bug: 35853185
Test: recovery_component_test passes.
Change-Id: I51e1ec946fa73761118fa1eaa082423df6d588e9
Add read_bootloader_message_from() and write_bootloader_message_to() to
allow specifying the BCB device (/misc).
Also add testcases for set_stage() and get_stage().
Test: recovery_component_test passes.
Test: Build a recovery image and apply a two-step OTA package.
Change-Id: If5ab06a1aaaea168d2a9e5dd63c07c0a3190e4ae
write_value(value, filename) writes 'value' to 'filename'. It can be
used to tune device settings when applying an OTA package. For example,
write_value("960000", "/sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq").
Bug: 32463933
Test: recovery_component_test passes.
Test: Apply an OTA package that contains a call to write_value(), and
check the result.
Change-Id: Ib009ecb8a45a94353f10c59e2383fe1f49796e35
'bool success = ExtractEntryToFile()' gives opposite result. Fix the
issue and add testcases.
Change the one-argument version of package_extract_file() to explicitly
abort for non-existent zip entry. Note that this is NOT changing the
behavior. Prior to this CL, it aborts from Evaluate() function, by
giving a general cause code. Now it returns kPackageExtractFileFailure.
BUg: 32903624
Test: recovery_component_test works.
Change-Id: I7a273e9c0d9aaaf8c472b2c778f7b8d90362c24f
Clean up SymlinkFn() a bit. Also clean up the temp files created when
running the tests; otherwise non-empty TemporaryDir won't be removed.
Test: recovery_component_test passes.
Change-Id: Id3844abebd168c40125c4dcec54e6ef680a83c3a
Changing the field of 'Value' in edify to std::string from char*.
Meanwhile cleaning up the users of 'Value' and switching them to
cpp style.
Test: compontent tests passed.
Bug: 31713288
Change-Id: Iec5a7d601b1e4ca40935bf1c70d325dafecec235
- Remove dead declarations in expr.h: SetError(), GetError(),
ClearError().
- Remove the declaration of Build() out of expr.h.
- Use std::unordered_map to implement RegisterFunction() and
FindFunction(); kill FinishRegistration().
- Add a testcase for calling unknown functions.
Test: mmma bootable/recovery; recovery_component_test passes.
Change-Id: I9af6825ae677f92b22d716a4a5682f58522af03b
Also add a testcase for sha1_check().
Test: mmma bootable/recovery; recovery_component_test passes.
Change-Id: I4d06d551a771aec84e460148544f68b247a7e721
So that we can write native tests for updater functions. This CL adds a
testcase for getprop() function.
Test: mmma bootable/recovery; Run recovery_component_test on device.
Change-Id: Iff4c1ff63c5c71aded2f9686fed6b71cc298c228
